Se connecter / S'enregistrer
Votre question

Connection wifi sous Slackware (Linux)

Tags :
  • Wifi
  • linux
  • Internet
Dernière réponse : dans Internet
26 Octobre 2009 01:05:09

Voila, j'aimerais me connecter avec la wifi avec slackware, mais probleme, ma carte wifi est bien installer mais je n'arrive pas a me connecter.

Voici le resultat de mon iwconfig :

  1. root@darkstar:/etc# iwconfig
  2. lo no wireless extensions.
  3.  
  4. eth0 no wireless extensions.
  5.  
  6. wlan0 IEEE 802.11g ESSID:off/any
  7. Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
  8. Bit Rate:1 Mb/s Sensitivity=-200 dBm
  9. RTS thr=2346 B Fragment thr=2346 B
  10. Encryption key:0000-2163-E9BD-F0 Security mode:restricted
  11. Power Management:off
  12. Link Quality:0 Signal level:0 Noise level:0
  13. Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
  14. Tx excessive retries:0 Invalid misc:0 Missed beacon:0


  1. root@darkstar:/# lspci -vv
  2. 05:01.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03)
  3. Subsystem: Netgear WG311v3 802.11g Wireless PCI Adapter
  4. Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
  5. Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
  6. Latency: 64, Cache Line Size: 32 bytes
  7. Interrupt: pin A routed to IRQ 17
  8. Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
  9. Region 1: Memory at febe0000 (32-bit, non-prefetchable) [size=64K]
  10. Capabilities: [40] Power Management version 2
  11. Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
  12. Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
  13. Kernel driver in use: ndiswrapper

  1. root@darkstar:/# ifconfig
  2. lo Link encap:Local Loopback
  3. inet addr:127.0.0.1 Mask:255.0.0.0
  4. inet6 addr: ::1/128 Scope:Host
  5. UP LOOPBACK RUNNING MTU:16436 Metric:1
  6. RX packets:1758 errors:0 dropped:0 overruns:0 frame:0
  7. TX packets:1758 errors:0 dropped:0 overruns:0 carrier:0
  8. collisions:0 txqueuelen:0
  9. RX bytes:148692 (145.2 KiB) TX bytes:148692 (145.2 KiB)
  10.  
  11. wlan0 Link encap:Ethernet HWaddr 00:1b:2f:d0:c1:c8
  12. UP BROADCAST MULTICAST MTU:1500 Metric:1
  13. RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  14. TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  15. collisions:0 txqueuelen:1000
  16. RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
  17. Interrupt:17 Memory:febe0000-febf0000

  1. root@darkstar:/# ping 127.0.0.1
  2. PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data.
  3. 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.020 ms
  4. 64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.021 ms
  5. 64 bytes from 127.0.0.1: icmp_seq=3 ttl=64 time=0.022 ms

  1. root@darkstar:/etc# cat resolv.conf
  2. search example.net

  1. root@darkstar:/etc# sudo route
  2. Kernel IP routing table
  3. Destination Gateway Genmask Flags Metric Ref Use Iface
  4. loopback * 255.0.0.0 U 0 0 0 lo

  1. root@darkstar:/# sudo dhclient wlan0
  2. Internet Systems Consortium DHCP Client V3.1.2p1
  3. Copyright 2004-2009 Internet Systems Consortium.
  4. All rights reserved.
  5. For info, please visit http://www.isc.org/sw/dhcp/
  6.  
  7. Listening on LPF/wlan0/00:1b:2f:xxxxxxx
  8. Sending on LPF/wlan0/00:1b:2:xxxxxx
  9. Sending on Socket/fallback
  10. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
  11. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9
  12. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15
  13. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
  14. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
  15. DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12
  16. No DHCPOFFERS received.
  17. No working leases in persistent database - sleeping.


  1. root@darkstar:/# iwlist wlan0 scanning
  2. wlan0 Scan completed :
  3.  
  4. Cell 01 - Address: 00:21:63:XX:XX:XX
  5. ESSID:"French_Connection"
  6. Protocol:IEEE 802.11g
  7. Mode:Managed
  8. Frequency:2.412 GHz (Channel 1)
  9. Quality:42/100 Signal level:-69 dBm Noise level:-96 dBm
  10. Encryption key:on
  11. Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
  12. 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
  13. 48 Mb/s; 54 Mb/s
  14. Extra:bcn_int=100
  15. Extra:atim=0



C'est pas un probleme de dhcp car j'ai deja 4 ordinateurs connectés par winxp et pas de soucis.

Autres pages sur : connection wifi slackware linux

26 Octobre 2009 02:05:26

Voici les infos de ma box.

LAN Interface
IP Address Subnet MAC Address Status
10.0.0.138 255.255.255.0 00:21:63:e9:bd:f0

WAN Interface
PVC VPI/VCI IP Address Subnet Gateway Encapsulation Status
PVC-0 8 /48 90.179.60.182 255.255.255.255 194.228.196.6 Route -PPPoE
PVC-1 8 /35 0.0.0.0 0.0.0.0 0.0.0.0 Bridge -RFC2684

Je dois peut etre modifier quelques choses ?
m
0
l
26 Octobre 2009 02:36:40

ok, mon inet addr est 10.0.0.22 Bcast : 10.0.0.255 Mask :255.255.255.0
Ce qui je pense est plus correct, mais sa ne fonctionne toujours pas...


J'essaye de ne pas regarder mon cd windows seven pour ne pas succomber a la tentation :D 
m
0
l
Tom's guide dans le monde
  • Allemagne
  • Italie
  • Irlande
  • Royaume Uni
  • Etats Unis
Suivre Tom's Guide
Inscrivez-vous à la Newsletter
  • ajouter à twitter
  • ajouter à facebook
  • ajouter un flux RSS